It looks like you’re visiting from the United States. For the best experience, please visit our U.S. website operated by Powerlube Industrial, our U.S. subsidiary and premium Memolub distributor.

Go to powerlubeind.com
MEMOLUB Visio Series Thumb

MEMOLUB VISIO SERIES KNOWLEDGE BASE

Read more Print Download User Guide Download Technical Data Sheet

INLEDNING

MEMOLUB® VISIO / VISIO PRO

MEMOLUB® VISIO och VISIO PRO är elektromekaniska smörjsystem för en eller flera smörjpunkter som finns i fyra storlekar (120 cc, 240 cc, 480 cc och 500 cc för OIL-R500-versionen).

VISIO-versionen är batteridriven, medan VISIO PRO-versionen drivs av en extern strömkälla på mellan 6 och 36 VDC. Den unika tvåkomponentskonstruktionen gör det möjligt att enkelt ta bort delar som behöver underhåll (patron och batterier) samtidigt som inställningarna förblir permanent fästa vid smörjpunkten.

Med ett högt smörjmedelsutmatningstryck på 25 bar erbjuder båda systemen ett brett spektrum av användningsområden som inte är möjliga med konventionella smörjare. De är utrustade med väl synliga, rundstrålande lysdioder som tydligt visar smörjarens status. För enkel kontroll finns en testknapp på enhetens undersida.

Visuella larm gör det möjligt för användaren att övervaka:

  • Korrekt pumpfunktion
  • Batterinivå (VISIO-versionen)
  • Om patronen är tom

VISIO PRO-versionen är särskilt lämplig för tillämpningar där maskinerna används sporadiskt eller sällan, samt för OEM-integration. Den kan även anslutas direkt till en PLC, vilket gör det möjligt att överföra och övervaka larmsignaler via maskinens styrsystem.

Båda versionerna kan monteras direkt på smörjpunkten eller installeras på avstånd. De kan smörja upp till 8 fettpunkter eller upp till 12 oljepunkter samtidigt.

Dimensioner

120CC

Grease & Oil

120cc I 4oz
Memolub Visio Series Dimentions 120

240CC

Grease & Oil

240cc I 8.1oz
Memolub Visio Series Dimentions 240

480CC

Grease & Oil

480cc I 16.2oz
Memolub Visio Series Dimentions 480

OIL R-500

Refillable Oil Reservoir

500cc I 16.9oz
Memolub Visio Series Dimentions 500 R

Försiktighetsåtgärder

  • Öppna inte höljet: spänd fjäder
  • Håll MEMOLUB® nedtryckt vid manuella kontroller
  • Leq <70 dB
  • Använd MEMOLUB® endast för smörjning av maskiner
  • Använd endast smörjpatroner och batterier som rekommenderas av tillverkaren
Memolub Visio Warnings

Specifikationer

Allmänt

MEMOLUB VISIO
Yttermått Ø101 mm, H138 (standard) till 251 mm (Giga)
Temperatur

Elektrisk

MEMOLUB VISIO MEMOLUB VISIO PRO
Strömkälla Batteri Extern – 6DIN M16-anslutning
Spänning 4,5 V DC (3 x 1,5 V DC AA) 6–36 V DC
PLC-anslutning Ej tillämpligt JA
Kortslutningsskydd Ja
Slaglängd 8 sekunder
Minsta slagintervall 15 minuter

Settings & Feedback

FREKVENSINSTÄLLNINGAR

2:A GENERATIONEN (SERIENUMMER VIS-XX-XXXX &amp; VPR-XX-XXXX)

WHEEL POSITION DOSING PERIODICITY MAX. DAILY OUTPUT* REFILLING FREQUENCY VS. CARTRIDGE CONTENT (120CC) REFILLING FREQUENCY VS. CARTRIDGE CONTENT (240CC) REFILLING FREQUENCY VS. CARTRIDGE CONTENT (480CC)
0** Externt (PLC)
1 48 timmar 0,3 cc/dag 12 månader 24 månader*** 48 månader***
2 24 timmar 0,6 cc/dag 6 månader 12 månader 24 månader***
3 16 timmar 0,9 cc/dag 4 månader 8 månader 16 månader***
4 12 timmar 1,2 cc/dag 3 månader 6 månader 12 månader
5 8 timmar 1,8 cc/dag 2 månader 4 månader 8 månader
6 6 timmar 2,4 cc/dag 1,5 månader 3 månader 6 månader
7 4 timmar 3,6 cc/dag 1 månad 2 månader 4 månader
8 2 timmar 7,2 cc/dag 0,5 månad 1 månad 2 månader
9 1 timme 14,4 cc/dag 0,25 månad 0,5 månad 1 månad

*Maximal daglig utmatning utan slaglager.

** Finns endast på Memolub Visio Pro-modeller.

*** Tänk på smörjmedlets utgångsdatum vid långa patronlivslängder.

VOLUME SETTINGS [cm³/day]

2ND GENERATION (SERIAL NUMBERS VIS-XX-XXXX & VPR-XX-XXXX)

By using stroke washers you can adjust the amount of lubricant discharged per pumping cycle.

NUMBER OF STROKE WASHERS WHEEL POSITION
0 1 2 3 4 5 6 7 8 9
- External (PLC) 0.3 0.6 0.9 1.2 1.8 2.4 3.6 7.2 14.4
External (PLC) 0.28 0.56 0.84 1.12 1.7 2.2 3.4 6.7 13.5
+ External (PLC) 0.26 0.52 0.79 1.04 1.62 2.1 3.15 6.3 12.6
2 + External (PLC) 0.24 0.49 0.73 0.98 1.46 1.95 2.92 5.85 11.7
3 + External (PLC) 0.22 0.45 0.67 0.9 1.35 1.8 2.7 5.4 10.8
4 + External (PLC) 0.2 0.41 0.62 0.82 1.23 1.65 2.47 4.95 9.9
5 + External (PLC) 0.18 0.37 0.55 0.74 1.1 1.5 2.2 4.5 9
6 + External (PLC) 0.17 0.34 0.5 0.68 1 1.35 2.02 4.05 8.1

*The circlip must always be added on top of the washers.

The circlip must always be added on top of the washers.

VISUAL FEEDBACK

2ND GENERATION (SERIAL NUMBERS VIS-XX-XXXX & VPR-XX-XXXX)

COLOR STATUS
The testrun has been activated through pushbutton . / The pumping cycle ran successfully.
Battery low / Lubricant cartridge empty.
Gearmotor damaged / Piston blocked.

See FAQ's section for detailed information

REMOTE INSTALLATION DISTANCES

TYPE OF INSTALLATION MAXIMUM DISTANCE*
Single point 8m
Multipoint with 2 outlets 6m
Multipoint with 4 outlets
Multipoint with 6 outlets
Multipoint with 8 outlets
Multipoint with 10 outlets Contact your distributor.
Multipoint with 12 outlets

*The maximum distances are valid for a variety of greases with a consistency level up to NGLI2. For oils, we generally consider the same distances multiplied by a factor 2.

KABELANSLUTEN STYRNING

As wired control features are available for the VISIO PRO, there are two different ways to use the device:

1) By defining a periodic expulsion mode on the local rotary encoder wheel (positions 1 to 9), with corresponding preset frequencies listed in the "FREQUENCY" section (see above).

2) By triggering single expulsion using the wired connection (6 DIN M16 connector - wires n1 & n2) - see CABLING section below for implementation.

Note that periodic and single expulsions are NOT exclusive: both may be active simultaneously. If you don't want the periodic expulsions to be active, please set the encoder wheel on position "0". If you don't want the external triggers to be active, please disconnect wires 1 & 2 or disable control from the PLC side.

INTERMITTENT LÄGE

MEMOLUB VISIO PRO

DESCRIPTION SIGNAL
INGÅNGSSIGNAL (FRÅN KUNDENS PLC/TIMER)
UTGÅNGSSIGNAL ”UPPTagen” (TILL KUNDENS PLC)
PUMPUTLOPP (TILL SMÖRJNING)
UTGÅNGSSIGNAL ”STANDARD” (TILL KUNDENS PLC)

KONTINUERLIGT LÄGE

MEMOLUB VISIO PRO

DESCRIPTION SIGNAL
INGÅNGSSIGNAL (FRÅN KUNDENS PLC/TIMER)
UTGÅNGSSIGNAL ”UPPTagen” (TILL KUNDENS PLC)
PUMPUTLOPP (TILL SMÖRJNING)
UTGÅNGSSIGNAL ”STANDARD” (TILL KUNDENS PLC)

KABEL

MEMOLUB VISIO PRO

The Memolub Visio Pro is delivered with a 6 x 0.25mm² cable with a 6DIN M16 female connector.

This connector has the 3 following functions:

1) To supply external power to the VISIO PRO, using the wires 3 & 6

2) To allow remote triggering of expulsions (i.e. from PLC), using the wires 1 & 2

3) To allow remote notification of alarms (i.e. to PLC) using the wires 4 & 5

If the remote controls 2) and 3) are not meant to be used, wires 1, 2, 4 and 5 are just not connected.

DESCRIPTION
1. EXTERNAL INPUT (OPTOCOUPLER INPUT +)
2. EXTERNAL INPUT (OPTOCOUPLER INPUT -)
3. POWER SUPPLY + (6-36VDC)
4. STATUS OUTPUT (OPTOCOUPLER COLLECTOR)
5. STATUS OUTPUT (OPTOCOUPLER EMITTER)
6. POWER SUPPLY - (0VDC)

INSTALLATION GUIDELINES

DIRECT INSTALLATION MEMOLUB VISIO + MEMOLUB VISIO PRO (2nd GENERATION)

MEMOLUB VISIO and MEMOLUB VISIO PRO must always be installed in the upright position. Failure to install the device upright may lead to potential damage to the automatic lubricator and to your equipment. Incorrect orientation will void the warranty and may pose safety risks.

MEMOLUB VISIO and MEMOLUB VISIO PRO are equipped with advanced machine learning capabilities, allowing it to account for environmental conditions when calculating its status. A learning period of 20 cycles is required, during which the lubricator must remain in the same environment without any changes to its position, fastening, support, or grease type. If any of these parameters are altered, the learning process can be reset by pressing and holding the pushbutton for more than 5 seconds.

  • 1

    B1

    Prime lube point and remove nipple.

  • 2

    B2

    Install VISIO Base using a strong threadlocker (BSP 1/4).

  • 3

    B3

    With setting key, choose wheel position according to "Settings" table above.

  • 4

    Direct installation step4

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 5

    Direct installation step5

    Screw tightly keeping the assembly aligned.

  • 6

    Direct installation step6

    Initialise Visio by pushing the button for 5 seconds.

  • 7

    E4b

    Initialisation is confirmed by flashing each color once.

  • 1

    B1

    Prime lube point and remove nipple.

  • 2

    B2

    Install VISIO Base using a strong threadlocker (BSP 1/4).

  • 3

    B3

    With setting key, choose wheel position according to "Settings" table above.

  • 4

    Direct installation step4

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 5

    Direct installation step5

    Screw tightly keeping the assembly aligned.

  • 6

    Direct installation step6

    Initialise Visio by pushing the button for 5 seconds.

  • 7

    E4b

    Initialisation is confirmed by flashing each color once.

DIRECT INSTALLATION MEMOLUB VISIO + MEMOLUB VISIO EP (1st GENERATION)

MEMOLUB VISIO and MEMOLUB VISIO EP must always be installed in the upright position. Failure to install the device upright may lead to potential damage to the automatic lubricator and to your equipment. Incorrect orientation will void the warranty and may pose safety risks.

  • 1

    B1

    Prime lube point and remove nipple.

  • 2

    B2

    Install VISIO Base using a strong threadlocker (BSP 1/4).

  • 3

    B3

    With setting key, choose wheel position according to "Settings" table above.

  • 4

    Direct installation step4

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 5

    Direct installation step5

    Screw tightly keeping the assemly aligned.

  • 6

    E4b

    VISIO initializes, flashes each color on, and makes one expulsion. Green lights confirm normal operation.

  • 1

    B1

    Prime lube point and remove nipple.

  • 2

    B2

    Install VISIO Base using a strong threadlocker (BSP 1/4).

  • 3

    B3

    With setting key, choose wheel position according to "Settings" table above.

  • 4

    Direct installation step4

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 5

    Direct installation step5

    Screw tightly keeping the assemly aligned.

  • 6

    E4b

    VISIO initializes, flashes each color on, and makes one expulsion. Green lights confirm normal operation.

REMOTE INSTALLATION MEMOLUB VISIO + MEMOLUB VISIO PRO (2nd GENERATION)

MEMOLUB VISIO and MEMOLUB VISIO PRO must always be installed in the upright position. Failure to install the device upright may lead to potential damage to the automatic lubricator and to your equipment. Incorrect orientation will void the warranty and may pose safety risks.

MEMOLUB VISIO and MEMOLUB VISIO PRO are equipped with advanced machine learning capabilities, allowing it to account for environmental conditions when calculating its status. A learning period of 20 cycles is required, during which the lubricator must remain in the same environment without any changes to its position, fastening, support, or grease type. If any of these parameters are altered, the learning process can be reset by pressing and holding the pushbutton for more than 5 seconds.

  • 1

    C1

    Prime lube point and remove nipple.

  • 2

    C2

    Secure the mounting bracket.

  • 3

    C3

    Install VISIO Base and F1/4 fitting on bracket using a strong threadlocker.

  • 4

    C4

    Install BSP 1/8 fitting on lube point.

  • 5

    C5

    Cut hose to required size.

  • 6

    C6

    Insert hose into bracket's quick fitting.

  • 7

    C7

    Insert hose into lube point's quick fitting.

  • 8

    C8

    With setting key, choose wheel position according to "Settings" table above.

  • 9

    C9

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 10

    C10

    Screw tightly keeping the assembly aligned.

  • 11

    C12bis

    VISIO initialises, flashes each color on to confirm successful installation.

  • 1

    C1

    Prime lube point and remove nipple.

  • 2

    C2

    Secure the mounting bracket.

  • 3

    C3

    Install VISIO Base and F1/4 fitting on bracket using a strong threadlocker.

  • 4

    C4

    Install BSP 1/8 fitting on lube point.

  • 5

    C5

    Cut hose to required size.

  • 6

    C6

    Insert hose into bracket's quick fitting.

  • 7

    C7

    Insert hose into lube point's quick fitting.

  • 8

    C8

    With setting key, choose wheel position according to "Settings" table above.

  • 9

    C9

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 10

    C10

    Screw tightly keeping the assembly aligned.

  • 11

    C12bis

    VISIO initialises, flashes each color on to confirm successful installation.

REMOTE INSTALLATION MEMOLUB VISIO + MEMOLUB VISIO EP (1st GENERATION)

MEMOLUB VISIO and MEMOLUB VISIO PRO must always be installed in the upright position. Failure to install the device upright may lead to potential damage to the automatic lubricator and to your equipment. Incorrect orientation will void the warranty and may pose safety risks.

  • 1

    C1

    Prime lube point and remove nipple.

  • 2

    C2

    Secure the mounting bracket.

  • 3

    C3

    Install VISIO Base and F1/4 fitting on bracket using a strong threadlocker.

  • 4

    C4

    Install BSP 1/8 fitting on lube point.

  • 5

    C5

    Cut hose to required size.

  • 6

    C6

    Insert hose into bracket's quick fitting.

  • 7

    C7

    Insert hose into lube point's quick fitting.

  • 8

    C8

    With setting key, choose wheel position according to "Settings" table above.

  • 9

    C9

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 10

    C10

    Screw tightly keeping the assembly aligned.

  • 11

    C12bis

    VISIO initializes, flashes each color on, and makes one expulsion. Green lights confirm normal operation.

  • 1

    C1

    Prime lube point and remove nipple.

  • 2

    C2

    Secure the mounting bracket.

  • 3

    C3

    Install VISIO Base and F1/4 fitting on bracket using a strong threadlocker.

  • 4

    C4

    Install BSP 1/8 fitting on lube point.

  • 5

    C5

    Cut hose to required size.

  • 6

    C6

    Insert hose into bracket's quick fitting.

  • 7

    C7

    Insert hose into lube point's quick fitting.

  • 8

    C8

    With setting key, choose wheel position according to "Settings" table above.

  • 9

    C9

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 10

    C10

    Screw tightly keeping the assembly aligned.

  • 11

    C12bis

    VISIO initializes, flashes each color on, and makes one expulsion. Green lights confirm normal operation.

MULTIPOINT INSTALLATION MEMOLUB VISIO + MEMOLUB VISIO PRO (2nd GENERATION)

MEMOLUB VISIO and MEMOLUB VISIO EP must always be installed in the upright position. Failure to install the device upright may lead to potential damage to the automatic lubricator and to your equipment. Incorrect orientation will void the warranty and may pose safety risks.

MEMOLUB VISIO and MEMOLUB VISIO PRO are equipped with advanced machine learning capabilities, allowing it to account for environmental conditions when calculating its status. A learning period of 20 cycles is required, during which the lubricator must remain in the same environment without any changes to its position, fastening, support, or grease type. If any of these parameters are altered, the learning process can be reset by pressing and holding the pushbutton for more than 5 seconds.

  • 1

    D1

    Prime lube point and remove nipple.

  • 2

    D2

    Secure the mounting bracket.

  • 3

    D3

    Install VISIO Base and F1/4 fitting on bracket using a strong threadlocker.

  • 4

    D4

    Install BSP 1/8 fitting on lube point.

  • 5

    D5

    Cut the hoses to required size.

  • 6

    D6

    Insert hoses into bracket's quick fittings.

  • 7

    D7

    Insert hoses into lube points' quick fittings.

  • 8

    D8

    With setting key, choose wheel position according to "Settings" table above.

  • 9

    D9

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 10

    D10

    Screw tightly keeping the assembly aligned.

  • 11

    D12

    VISIO initializes, flashes each color on, and makes one expulsion. Green lights confirm normal operation.

  • 1

    D1

    Prime lube point and remove nipple.

  • 2

    D2

    Secure the mounting bracket.

  • 3

    D3

    Install VISIO Base and F1/4 fitting on bracket using a strong threadlocker.

  • 4

    D4

    Install BSP 1/8 fitting on lube point.

  • 5

    D5

    Cut the hoses to required size.

  • 6

    D6

    Insert hoses into bracket's quick fittings.

  • 7

    D7

    Insert hoses into lube points' quick fittings.

  • 8

    D8

    With setting key, choose wheel position according to "Settings" table above.

  • 9

    D9

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 10

    D10

    Screw tightly keeping the assembly aligned.

  • 11

    D12

    VISIO initializes, flashes each color on, and makes one expulsion. Green lights confirm normal operation.

MULTIPOINT INSTALLATION MEMOLUB VISIO + MEMOLUB VISIO EP (1st GENERATION)

MEMOLUB VISIO and MEMOLUB VISIO EP must always be installed in the upright position. Failure to install the device upright may lead to potential damage to the automatic lubricator and to your equipment. Incorrect orientation will void the warranty and may pose safety risks.

  • 1

    D1

    Prime lube point and remove nipple.

  • 2

    D2

    Secure the mounting bracket.

  • 3

    D3

    Install VISIO Base and F1/4 fitting on bracket using a strong threadlocker.

  • 4

    D4

    Install BSP 1/8 fitting on lube point.

  • 5

    D5

    Cut the hoses to required size.

  • 6

    D6

    Insert hoses into bracket's quick fittings.

  • 7

    D7

    Insert hoses into lube points' quick fittings.

  • 8

    D8

    With setting key, choose wheel position according to "Settings" table above.

  • 9

    D9

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 10

    D10

    Screw tightly keeping the assembly aligned.

  • 11

    D12

    VISIO initializes, flashes each color on, and makes one expulsion. Green lights confirm normal operation.

  • 1

    D1

    Prime lube point and remove nipple.

  • 2

    D2

    Secure the mounting bracket.

  • 3

    D3

    Install VISIO Base and F1/4 fitting on bracket using a strong threadlocker.

  • 4

    D4

    Install BSP 1/8 fitting on lube point.

  • 5

    D5

    Cut the hoses to required size.

  • 6

    D6

    Insert hoses into bracket's quick fittings.

  • 7

    D7

    Insert hoses into lube points' quick fittings.

  • 8

    D8

    With setting key, choose wheel position according to "Settings" table above.

  • 9

    D9

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 10

    D10

    Screw tightly keeping the assembly aligned.

  • 11

    D12

    VISIO initializes, flashes each color on, and makes one expulsion. Green lights confirm normal operation.

CHECK FUNCTION

2ND GENERATION

  • 1

    E1b

    Locate the push button on the bottom of the memo.

  • 2

    E2b

    Push the button.

  • 3

    E4b

    Memolub Visio / Visio Pro initialises, flashing each color on successively.

  • 4

    E5

    Memolub Visio / Visio Pro makes 1 expulsion.

  • 5

    E6

    After scanning all parameters, VISIO flashes green lights in case of normal operation. For any other colors, please refer to the FAQ section.

  • 1

    E1b

    Locate the push button on the bottom of the memo.

  • 2

    E2b

    Push the button.

  • 3

    E4b

    Memolub Visio / Visio Pro initialises, flashing each color on successively.

  • 4

    E5

    Memolub Visio / Visio Pro makes 1 expulsion.

  • 5

    E6

    After scanning all parameters, VISIO flashes green lights in case of normal operation. For any other colors, please refer to the FAQ section.

1ST GENERATION

  • 1

    E1

    Locate the green triangular label indicating touchpad

  • 2

    E2

    Keep your fingers under VISIO Base, below the triangular sign. Blinking of the 4 green lights confirm activation of the touchpad.

  • 3

    E3

    Once the total touch duration has reached 5 sec, the 4 green lights are turned on simultaneously for 1s.

  • 4

    E4

    VISIO initializes, flashing each color on successively.

  • 5

    E5

    VISIO makes 1 expulsion.

  • 6

    E6

    After scanning all parameters, VISIO flashes green lights in case of normal operation. For any other colors, please refer to the FAQ section.

  • 1

    E1

    Locate the green triangular label indicating touchpad

  • 2

    E2

    Keep your fingers under VISIO Base, below the triangular sign. Blinking of the 4 green lights confirm activation of the touchpad.

  • 3

    E3

    Once the total touch duration has reached 5 sec, the 4 green lights are turned on simultaneously for 1s.

  • 4

    E4

    VISIO initializes, flashing each color on successively.

  • 5

    E5

    VISIO makes 1 expulsion.

  • 6

    E6

    After scanning all parameters, VISIO flashes green lights in case of normal operation. For any other colors, please refer to the FAQ section.

REFILL GUIDELINES

CARTRIDGES

  • 1

    A1

    Remove VISIO Module from VISIO Base.

  • 2

    A2

    Open VISIO Module (fingers on ribs).

  • 3

    A3

    Prime VISIO Pump.

  • 4

    A4

    Insert new battery pack and seal. NOTE: the battery seal can be removed for 480cc cartridges

  • 5

    A5

    Squeeze air out of the cartridge.

  • 6

    A6

    Replace the cartridge on VISIO Pump.

  • 7

    A7

    Close and lock VISIO Module (fingers on ribs).

  • 8

    A8

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 9

    A9

    Screw tightly keeping the assembly aligned.

  • 10

    E4b

    VISIO initializes, flashes each color on, and makes one expulsion. Green light confirms proper functioning.

  • 1

    A1

    Remove VISIO Module from VISIO Base.

  • 2

    A2

    Open VISIO Module (fingers on ribs).

  • 3

    A3

    Prime VISIO Pump.

  • 4

    A4

    Insert new battery pack and seal. NOTE: the battery seal can be removed for 480cc cartridges

  • 5

    A5

    Squeeze air out of the cartridge.

  • 6

    A6

    Replace the cartridge on VISIO Pump.

  • 7

    A7

    Close and lock VISIO Module (fingers on ribs).

  • 8

    A8

    Align the pin of VISIO Module with the notch of VISIO Base.

  • 9

    A9

    Screw tightly keeping the assembly aligned.

  • 10

    E4b

    VISIO initializes, flashes each color on, and makes one expulsion. Green light confirms proper functioning.

VIDEOR

Vanliga frågor

  • Nothing happens after screwing the module on the base.

    • The pin of the module is possibly not proper aligned with the notch of the base. Unscrew the module from the base, align correctly and screw it again.
    • Memolub VISIO Series is not tightly screwed to the memo. Turn it clockwise until stop.
    • There is possibly no battery inside the module. Insert 3x 1,5 VDC AA batteries to resolve the issue.
    • There is possibly something obstructing the communication between the base and the module contacts. Unscrew the module from the base, remove any dust or obstacles from the base and the module contacts and screw back together tightly.

  • The touchpad does not work after initialisation was completed successfully.

    Your Memolub VISIO Series possibly initialised in an unstable environment. Unscrew the base from the module and screw again to reset the system. Wait until one expulsion is performed and you observe green lights, indicating the initialization is complete.

  • The red lights are blinking periodically.

    • There is possibly a too high back pressure present in the system. Inspect your downstream piping to remove any clogging or jam. Activate the touchpad and check for at least 2 expulsions if the systems operate fine.
    • There is possibly something obstructing the communication between the base and the module contacts. Unscrew the module from the base, remove any dust or obstacles from the base and the module contacts and screw back together tightly.
    • The motor is broken. Replacement of the module is necessary.

  • The yellow lights are blinking periodically.

    • There is possibly something obstructing the communication between the base and the module contacts. Unscrew the module from the base, remove any dust or obstacles from the base and the module contacts and screw back together tightly.
    • The batteries are empty. Replacement of the battery pack is necessary.

  • The blue lights are blinking periodically.

    • The cartridge is possibly out of grease. Replacement of the cartridge is necessary.
    • The system is not primed. Prime the system using a manual grease pump.
    • The system is operating out of its minimum and maximum temperature range. Please make sure the system is operating within the recommended temperature range.

REGELVERKSAM INFORMATION

SYMBOL DESCRIPTION
This product is compliant with Directives 2006/42/EC (Machinery). The relevant Declaration of Conformity is available here.
This product is compliant with UK regulations 2008 No. 1597 (Supply of Machinery). The relevant Declaration of Conformity is available here.
This product is compliant with customs union technical regulation TR CU 010/2011 (safety of machines and equipment). The relevant Declaration of Conformity is available here.
The WEEE symbol is attached to the product in compliance with the EU directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). It is intended to deter the improper disposal of this product and to promote reuse and recycling.
The packaging material can be recycled. Please arrange for the environmental appropriate disposal of the packaging.